Nordic Farrier Tools
Viking Tools
Click Photo to Enlarge
|
Viking 15" Nipper |
|
|
Click Photo to Enlarge |
Item # NFJP15P & NFJP15SP Forged from high quality tool steel, machined to precise tolerances and heat treated for wear resistance. Offers a very sharp cut. The 15" Nipper is available completely polished or semi-polished. Designed for trimming horses hoofs only. Do not use to cut wire or nails! Packed 1 per ctn. Ctn. weight 2-1/4 lbs. |
|
Viking 14" Race Track Nipper |
|
|
Click Photo to Enlarge |
Item # NFJP14RP & NFJP14RSP
The 14" race track nipper forged from high quality tool steel, machined to precise tolerances and heat treated for wear resistance. Blades are sharpened by hand for accurate and very sharp cutting. Farriers find this nipper works well on running and performance horses. The 14" Nipper is available completely polished or semi-polished. Designed for trimming horses hoofs only. Do not use to cut wire or nails! Packed 1 per ctn. Ctn. weight 2 lbs. |
|
Viking 12" Nipper |
|
|
Click Photo to Enlarge |
Item # NFJP12P & NFJP12SP
The 12" is the smallest of the nippers and is ideal for smaller-hoofed horses. This nipper is of the same quality as the 14" providing the farrier maximum precision with minimum fatigue during daily use.. The 12" Nipper is available completely polished or semi-polished. Designed for trimming horses hoofs only. Do not use to cut wire or nails! Packed 1 per ctn. Ctn. weight 1-3/4 lbs. |
|
Viking Curved Jaw Clincher |
|
|
Click Photo to Enlarge |
Item # 116CP and 116CSP The Curved Bottom Jaw Clinchers were introduced due to farrier demand. Featuring a slightly curved bottom jaw, this high quality tool is offered in either the completely polished finish for the professional or only the head polished and handles sanded for a considerable cost savings. Packed 1 per ctn. Ctn. weight: 1 lb. 6 oz. |
|
Viking Straight Jaw Clincher |
|
|
Click Photo to Enlarge |
Item # 116SP and 116SSP The 116SP is completely polished for the professional appearance while providing a very smooth feel. The 116SSP features a fully polished head while the handles have been lightly sanded to remove any sharp burrs and provides a cost savings advantage. Both clinchers are forged from high quality tools steel, precision machined, and heat treated for strength and durability. Packed 1 per ctn. Ctn. weigh: 1 lb. 6 oz. |
|
Viking Shoe Puller & Spreader |
|
|
Click Photo to Enlarge |
Item # NFJP12PO The NFJP12PO is Nordic Forge's new combination shoe puller/ spreader which is forged and heat treated for strength. The polished tool has sharp teeth on outside edges for ease in spreading most shoe sizes and styles. The round knobs on handle ends make tool selection easy. Packed 1 per ctn. Ctn. weight: 1.5 lbs. |
|
Viking Rounding Hammers |
|
|
Click Photo to Enlarge |
Item # 285HT - 2 lb. Rounding Hammer Item #286HT - 1 1/2 lb. Rounding Hammer
Forged from high quality tool steel, machined to exacting tolerances, and then carefully heat treated. After heat treat, the heads undergo a unique process that gives them a superior finish while rounding the chamfers to help prevent chipping. Both hammers feature new Arkansas hickory burnt and buffed handles. Packaged 1 per ctn. Ctn. weight: 285HT 2-3/4 lbs. & 286HT 1-3/4 lbs. |
|
Click Photo to Enlarge |
Item # 287 - 1 lb. 10 oz. Rounding Hammer Forged from high quality tool steel, precision machined to exacting tolerances, and then carefully heat treated and hand polished to a superior finish. Burnt and buffed Arkansas hickory handle which is oversized for the farrier to file and sand for a custom fit. Packaged 1 per ctn. Ctn. weight: 2-3/4 lbs. |
|
Click Photo to Enlarge |
Item # 288 - Clipping Hammer Forged from high quality tool steel, precision machined to exacting tolerances and then carefully heat treated and hand polished to a superior finish. This hammer also features an oversized burn and buffed Arkansas hickory handle for the farrier to file and sand for a custom fit. Packed 1 per ctn. Ctn. weight: 2-3/4 lbs. |
|
Viking S7 Pritchel |
|
|
#NS7A Click Photos to Enlarge |
Item # NS7 and NS7A
Precision machined from S7 tool steel, then heat treated and hand polished to a superior finish. This tool is designed for hot work. Always wear safety glasses when using striking tools. Overall length is 10-1/2 inches. Item #NS7
The Angle Pritchel was designed to back punch shoes, you can move the pitch of the hole in or out. If you turn the straight side to the out side of the shoe the pitch will move in, turn the straight side to the inside of the shoe the pitch will move out. Item #NS7A
Packed 1 per ctn. Ctn. weight: 1 lb. |
|
Viking Farrier Tool Kit |
|
|
Click Photo to Enlarge |
Item #5075
Attractive 9-piece farrier tool kit for student or full-time farrier, designed specifically for trimming horses hooves. Contains one each of the following hoof trimming instruments: No.103J Hoof Pick, No.1180 Victorinox RH Hoof Knife, No.116CP Curved Jaw Polished Clincher, No.285HT 2 lb. Viking Rounding Hammer, No.NFJP15P 15" Polished Viking Nipper, No. 900 Blackmaster Rasp with wooden handle, No.284 14 oz. Driving Hammer, No. NS7 Nordic S7 Pritchel, No.109 Nordic Clinch Cutter. Packed 1 per ctn. Ctn. weight: 11.3 lbs. |
|
Nail Clincher |
Item # 116 |
|
Click Photo to Enlarge |
Professionally forged for use on high and low nails. Used to roll over nails with the curved jaw. Cushion-grip handles. Packed 6 per ctn. Ctn. weight: 6-1/4 lbs. |
| Hoof Nipper | Item # 104PFH |
|
Click Photo to Enlarge |
Designed exclusively for trimming hooves. This 14-inch long professional nipper features a wide 1" flat head and thin heat-treated jaw. Cushion-grip handles. Do not use on hardened nails or wire. Packed 6 per ctn. Ctn. weight: 11-1/2 lbs |
|
Hoof Nipper |
Item # 104P |
|
Click Photo to Enlarge |
This forged steel nipper features a heavier jaw than the 104PFH allowing for less chance of misuse by an amateur. Harden jaw. 14" long. Cushion grip handles. Do not use on hardened nails or wire. Packed 6 per ctn. Ctn. weight: 11-1/2 lbs. |
|
Clinch Cutter |
Item # 109 |
|
Click Photo to Enlarge |
Forged from quality tool steel our buffer features a bevel on one side and flat surface on reverse for close cutting. Pritchel on opposite end for opening and sizing nail holes. 7" in length. Packed 6 per ctn. Ctn. weight: 4 1/2 lbs. |
|
Pritchel |
Item # 108 |
|
Click Photo to Enlarge |
Machined from quality tool steel with hardened point. Used to open and resize nail holes. 5/8" x 12". Packed 6 per ctn. Ctn. weight: 6 lbs. |
|
CAUTION: ALWAYS WEAR GOGGLES WHEN USING STRIKING TOOLS!! |
|
CAUTION: ALWAYS WEAR GOGGLES WHEN USING STRIKING TOOLS!! |
|
Farrier Rounding Hammers |
Forged from quality tool steel. Perfectly balanced with one face round crowned and one face flat with beveled edges to reduce the possibility of chipping. Arkansas hickory handles. | ||||
|
Click Photo to Enlarge |
No. |
Description | Ctn. Pack | Ctn. Weight | |
|
285 |
2 lb. w/15-1/2" handle | 1 | 2-3/4 lbs. | ||
|
Click Photo to Enlarge |
286 |
1 lb. 8 oz. w/14" handle | 1 | 1-3/4 lbs. | |
HAMMER HANDLES: 203H handle for 110, 283, and 284 driving handles
204H handle for 286 rounding hammer
205H handle for 285 rounding hammer
|
CAUTION: ALWAYS WEAR GOGGLES WHEN USING STRIKING TOOLS!! |
| Hoof Nipper | Item # 106PFH |
|
Click Photo to Enlarge |
Designed exclusively for trimming hooves. This 14" long newly designed professional nipper features a wide 1 1/8" flat head and thin heat- treated jaw. Cushion grip handles. Do not use on hardened nails or wire. Packed 6 per ctn. Ctn. weight: 11 lbs. |
|
CAUTION: ALWAYS WEAR GOGGLES WHEN USING STRIKING TOOLS!! |
|
Professional Hoof Trimming Kit |
Item #5050 |
|
Click Photo to Enlarge |
An attractive set makes a perfect gift. A pop-up self display lid makes it great for display merchandising. Contains one each of the following hoof trimming instruments: No. 283 Hammer, No. 104PFH Nipper, No. 114 Hoof Knife, No. 1110 Rasp, No. 8 Handle, No. 109 Clinch Cutter, No. 103 Hoof Pick, No. 116 Clincher, No. 108 Pritchel, for a total of nine items. Designed especially for trimming hooves and shoeing horses. Can be used for cattle, too. Packed 1 per ctn. Ctn. weight: 9 lbs. |
|
CAUTION: ALWAYS WEAR GOGGLES WHEN USING STRIKING TOOLS!! |
Home Horseshoes Horseshoe Nails Other Farrier Supplies Contact Us
All Nordic Tools are made in the U.S.A.
Updated November 12, 2007